Jul 25, 2017

Decorative Material construction on the wall after the end of the bubble, how to do?
Decorative Material through the end of the reasons: If the wall color, thin light Decorative Material paste up, there will be through the end of the phenomenon. This is because the color of the decorative material is too shallow or too thin to cover the color of the wall. Dark or thick Decorative Material can cover the wall color, rarely appear through the end of the phenomenon. There are colored walls.
To avoid Decorative Material through the end of the method:
The best way to avoid the phenomenon is to treat the wall into a color, preferably white. Only the wall without color, Decorative Material on the wall, it will not appear through the end of the phenomenon and affect the use of results.
Tips:
Careful friends will find that the picture above the bottom of the phenomenon of Decorative Material, is due to the wall painted varnish, and the top part of the wall is white latex paint, resulting in serious wall color caused. Why is this so?
(1) the general old house wall brush is a varnish, but the ceiling is painted latex paint. Ceiling in the brush when the latex paint, if the top part of the wall is also painted, it will cover a part of the varnish, so that the area of the wall into white, resulting in color.
(2) thin light Decorative Material, especially imitation silk fabric, due to the characteristics of thin silk fabric, paste up after the yellow varnish and white latex paint part will show the depth of different colors, that is, through the bottom phenomenon.
Therefore, brush the old house of varnish, if the varnish was covered with latex paint, be sure to re-putty treatment of the wall, and brushing the base film, so paste the decorative material will not appear after the end of the phenomenon. In addition, the old room posted new Decorative Material, the wall may also exist for other reasons the color difference, we must pay attention.
So what about the spill? Because different Decorative Material manufacturers Decorative Material quality is not the same, and Decorative Material construction master technology is also good or bad, it will lead to Decorative Material exist overflow phenomenon.
Why the Decorative Material will overflow glue?
Due to Decorative Material have a certain micro-hole, when the Decorative Material in the Decorative Material if the plastic material is better (rubber thin, open time is short), paste the decorative material when the colloid is easy to penetrate along the decorative material microporous, if the Decorative Material Colloid stereotypes have been dry before, then with the extension of time, the colloid will penetrate to the surface of Decorative Material, resulting in Decorative Material discoloration, if the surface of the decorative material is decorated with gold or Decorative Material easy to discoloration (pigment instability, susceptible to acid, Salt, water and other corrosion), this situation can only be re-tear and then re-paste, if the decorative material is not easy to change color, you can re-wetting the decorative material after the clean and dry ventilation to avoid Decorative Material such as color change later The
To prevent Decorative Material overflow plastic construction of the attention to what?
If for the sake of beauty and performance, choose a thin, low density, no bottom coating, non-cross fabric and other types of Decorative Material, such as imitation silk Decorative Material, embroidery, natural fiber weaving, etc., as long as attention to the construction method can be resolved of:
1, to choose Decorative Material for plastic, ordinary wallpaper glue corresponding to the development of wallpaper can not take into account the Decorative Material, and Decorative Material for the characteristics of Decorative Material for the development of Decorative Material more suitable for use;
2, glue to adjust some of the thick coating, the use of plastic on the wall, pay attention to the colloid must be coated evenly, when the scratch to light scraping;
3, if the plastic tone of the thin, you can use the wall after a long time to open the glue, so that glue slightly sticky "table dry" when the paste, this can also reduce the plasticity of the plastic to ensure faster stereotypes, especially the case To the wall grass-roots density is not high permeability of the wall, but also to increase the opening time of plastic;
4, paste and other Decorative Material after the basic stereotypes to be timely and dry ventilation, reduce the moisture content of wall Decorative Material, reduce colloid penetration time.
If you have produced spilled glue then how to deal with it?
Seamless decorative material at the end of material points: hot sol Decorative Material, non-woven Decorative Material
1, hot sol Decorative Material of the glue treatment:
Hot sol is generally not easy to glue, but if the construction of long-term ironing the same place, iron high temperature steam water dissolved in the hot sol, the colloid through the fiber through the cloth quickly curing, so the hot sol is not easy to glue , But once the glue is almost no way to deal with.
Permeating the hot plastic feels like the texture is relatively hard, generally you can try with a small brush and so on brush, the cloth pattern of the plastic handle, but the effect is not obvious. Large range of glue is not recommended to repair.
2, non-woven Decorative Material, plastic infiltration:
Once the non-woven fabric overflow glue, glue is easily diluted through the water into the non-woven fabric, so the glue marks is difficult to clean. In the glue marks before drying with a wet sponge for a small range of suction, avoid extensive wipe, so as not to expand the scope of pollution. After the stickers are dry, they can be wiped with a clean white towel.